-
101
-
102
Determination of rational values of the parameters of the container depot
Published 2021-12-01“…Today, due to the increase in rail freight traffic, there is a shortage of containers, and the issue of shortage of containers has not been resolved for a long time. …”
Get full text
Article -
103
Provisioning of Live Container Migration in Edge/Cloud Environments: Techniques and Challenges
Published 2025-06-01“… Containers have become increasingly popular in the virtualization landscape. …”
Get full text
Article -
104
External Factors Influence on Defects Detection by Scanning Contact Potentiometry
Published 2024-12-01“…Scanning contact potentiometry (SCP) method was used to detect structural inhomogeneities in a welded joint under the application of heat and constant electric current. …”
Get full text
Article -
105
Contact Dermatitis Caused by Topical Minoxidil: Allergy or Just Irritation
Published 2025-04-01“…This article presents a systematic review of the current literature, evaluating minoxidil-induced allergic contact dermatitis. …”
Get full text
Article -
106
Piezoresistive Cantilever Microprobe with Integrated Actuator for Contact Resonance Imaging
Published 2025-01-01“…However, noise is greatly increased with the bending mode and contact force increasing on viscoelastic samples. …”
Get full text
Article -
107
DEVELOPMENT AND EFFICIENCY EVALUATION OF CARGO TRANSPORTATION TECHNOLOGY IN HIGH-CAPACITY CONTAINERS WITH LOAD LIFTING VERTICAL STAYS IN ROADRAIL NETWORK
Published 2020-07-01“…At present the transportation of current high-capacity containers in road-rail mixed network is carried out only by means of the specialized sites with the equipment for their reloading. …”
Get full text
Article -
108
Evolution of the Contact-Fatigue Defects Caused Rail Failure Rate
Published 2015-06-01“…There is discussed current situation and problems of rail damageability in operation. …”
Get full text
Article -
109
-
110
Study on Improving Condensing Capacity of 30B Container
Published 2025-04-01“…The results show that the best heat dissipation effect is achieved when the forced air cooling wind direction and the impact angle of the cylindrical container are 180°,and the container condensation efficiency is increased by 14.5% on average at 263.15 K,wind speed of 3 m/s,calculation length of 2400 s,and 70 cooling ribs compared with that when there is no loading of cooling ribs,and the average cooling efficiency is improved by 14.9% after optimizing the design of cooling ribs,and the cooling efficiency is increased by 19.9%,and at 248.15 K,with a wind speed of 3 m/s,the average thermal efficiency is improved by 30.4%. …”
Get full text
Article -
111
Friction in Oil-Lubricated Rolling–Sliding Contacts with Technical and High-Performance Thermoplastics
Published 2024-10-01“…Oil lubrication allows for their usage in high-power-transmission applications, such as gears. The current design guidelines for thermoplastic gears lack reliable estimates for the coefficient of friction of oil-lubricated rolling–sliding contacts. …”
Get full text
Article -
112
A review of bioremediation of textile dye containing wastewater
Published 2025-12-01“…The increasing prevalence of synthetic dyes in wastewater has become a significant environmental issue, primarily due to their extensive utilization in diverse industries such as textiles, food manufacturing, and pharmaceuticals. …”
Get full text
Article -
113
The analysis of carrier transport mechanism at the interface of BZOPET-GR Schottky contact
Published 2025-01-01“…X-ray Photoelectron Spectroscopy (XPS) analysis revealed a reduction in oxygen vacancies with increasing B ion doping. The current–voltage (I-V) characteristics of the Schottky contacts were systematically investigated over a temperature range of 160–300 K. …”
Get full text
Article -
114
-
115
An Investigation in the I-gate Body Contact for Partially Depleted SOI MOSFET
Published 2024-02-01“…The drain induced barrier lowering of the center transistor is increased by 30% and off-current 40 times than that of the first transistor. …”
Get full text
Article -
116
Contact of working surfaces for spherical washers and recommendations for determining the gap in the joint
Published 2020-12-01“…In the article was proposed to introduce into the technical requirements for the spherical washers drawings changes concerning the gap size allowable in the conjunction, and as well as tolerances value changes of the radii of the working surfaces of the washers, thus increasing their manufacturability without conflicting with the requirements of the current standards.…”
Get full text
Article -
117
Analysis of thermal effects according to channel and drain contact metal distance
Published 2025-01-01Get full text
Article -
118
Mechanism of wellbore instability considering tubular-string contact with the wellbore wall
Published 2025-07-01“…Tubular strings in the wellbore are highly prone to wellbore wall contact. However, most current studies on wellbore instability neglect the contact interaction between tubular strings and the wellbore during drilling, wiper tripping, and casing running operations. …”
Get full text
Article -
119
Influence of Contact Ultrasound Assisted Vibrating Plate on the Freezing Rate of Carrot
Published 2017-01-01“…Ultrasound can promote the formation of crystal nucleus, shorten the freezing time and get a higher quality freeze, but the technology is currently used for the liquid samples or immersion freezing process, and solid samples were barely taken into account. …”
Get full text
Article -
120
THE RELIABILITY OF DETERMINING THE SHORT CIRCUIT ZONE OF THE LINES OF 6–35 kV
Published 2018-01-01“…A method of increasing the reliability of determining the zone of short-circuit at the current step protection of the lines of 6–35 kV with unilateral power, aimed at improvement of their technical perfection, is presented in the paper. …”
Get full text
Article