Rolling production. Tube rolling

Rolling production. Tube rolling

.

Saved in:

Bibliographic Details
Format:	Article
Language:	English
Published:	Belarusian National Technical University 2009-05-01
Series:	Литьë и металлургия
Online Access:	https://lim.bntu.by/jour/article/view/1035
Tags:	Add Tag No Tags, Be the first to tag this record!

Similar Items

Optimization of Roll Configuration and Investigation of Forming Process in Three-Roll Planetary Rolling of Stainless Steel Seamless Tubes
by: Chuanchuan Ma, et al.
Published: (2025-05-01)

Rolling production. Sorting rolling shop
Published: (2009-05-01)

Influence of the wall thickness value on the cross wall thickness deviation of tubes rolled on the tube rolling plant with the continuous mill
by: Pilipenko S. V., et al.
Published: (2018-06-01)

PERFECTION OF PRODUCTION TECHNOLOGY OF REBARS OF SMALL SECTIONS, ROLLED BY MULTISTRAND ROLLING-AND-SEPARATION
by: S. M. Zhuchkov, et al.
Published: (2009-08-01)

Ceramic rolls for rolling of steel foils
by: Vyacheslav Goryany, et al.
Published: (2023-03-01)

STRENGTH ANALYSIS OF BANDED ROLL FOR ASYMMETRIC ROLLING
by: L. A. Isaevich, et al.
Published: (2016-12-01)

DEVELOPMENT AND MASTERING OF SOFTWARE FOR REGISTRATION OF THE PRODUCTION TESTING RE¬SULTS OF TUBE-ROLLING SHOP OF RUP «BMZ»
by: V. D. Rahmanchik, et al.
Published: (2011-09-01)

Improving the technology of producing seamless hot‑rolled pipes from stainless steel l80 type 13Cr in the tube rolling workshop
by: A. V. Strelchenko, et al.
Published: (2024-06-01)

CONTROLLING IN ROLLING PRODUCTION OF ОАО «BMZ»
by: V. M. Machulin, et al.
Published: (2012-02-01)

Metal consumption rates in rolling production
by: S. A. Kashko
Published: (2022-05-01)

THE INCREASE OF SERVICE DURABILITY OF THE TECHNOLOGICAL TOOL OF PIERCING MILL OF THE TUBE-ROLLING SHOP
by: A. V. Vengura, et al.
Published: (2013-11-01)

Algorithm for optimization of cold‑rolled pipe rolling routes
by: S. V. Pilipenko
Published: (2024-09-01)

Rheological characteristics of steel in continuous roll casting-rolling
by: Ольга Холявік, et al.
Published: (2021-12-01)

Research on remaining life of rolling bearings for rolling stock
by: ZHANG Zongfeng, et al.
Published: (2023-11-01)

Rolling with the Punches
by: Mogamat Reederwan Craayenstein, et al.
Published: (2020-08-01)

Roll with the changes
by: Nathan Blow
Published: (2014-04-01)

Surrogate-assisted optimization of roll-to-roll slot die coating
by: Christopher Passmore, et al.
Published: (2025-08-01)

Rolling Force Prediction of Hot Rolling Based on GA-MELM
by: Jingyi Liu, et al.
Published: (2019-01-01)

DBO-DELM Method for Predicting Rolling Forces in Cold Rolling
by: LI Xiaoyang, et al.
Published: (2024-12-01)

Residual Life of Rolling Bearings for Railway Locomotives and Rolling Stock
by: Zongfeng ZHANG, et al.
Published: (2019-01-01)

Research on the effect of the grooving of mill rolls of the reeling tube mill on the wear of the elongating mandrel
by: Yu. L. Bobarikin, et al.
Published: (2019-01-01)

Study on the Influence of Mandrel Speed on the Titanium Tube Continuous Retained-Mandrel Rolling Process
by: Chao Li, et al.
Published: (2024-09-01)

Economization of production of the mill bar and rolled wire
by: S. M. Zhuchkov
Published: (2003-08-01)

MINIMIZATION OF PLANTS ON PRODUCTION OF HOT-ROLLED PLATE
by: And. I. Rozhkov, et al.
Published: (2010-11-01)

UNTRADITIONAL APPROACHES TO THE DEVELOPMENT OF SECTION ROLLING PRODUCTION
by: S. M. Zhuchkov, et al.
Published: (2006-05-01)

Research of defects of hot-rolled steel having rolling nature of formation of the rolling shop no. 1 of rolling mill 850 at OJSC «BSW – Management Company of Holding «BMC»
by: I. A. Kovaleva, et al.
Published: (2019-08-01)

The development and introduction of production technology and heat treatment of seamless hot-rolled tubes from cr-mo steel grades
by: S. N. Аudeev, et al.
Published: (2019-01-01)

Data-driven fault detection and positioning of eccentric rolls in roll-to-roll systems using wrap angle and sensor proximity
by: Yoonjae Lee, et al.
Published: (2024-12-01)

TERMS OF USING OF THREE-FOCUSED ROLLING MODULE IN THE PROCESS OF BAR ROLLING
by: S. M. Zhuchkov, et al.
Published: (2005-02-01)

Strength analysis of banded roll for asymmetric rolling of few-leaf springs
by: L. A. Isaevich, et al.
Published: (2018-10-01)

DEVICE AND METHODS FOR RESEARCH ROLLING FRICTION AND CONTACT ADHESIONE IN PRE-ROLLING
by: I. Z. Gilavdary, et al.
Published: (2015-03-01)

Characteristic points of roll contact curves of a two-roll module
by: Khalturaev Farkhod, et al.
Published: (2025-01-01)

Analysis and development of the method for calculating calibration of the working plank in the cold tube roller rolling mills
by: S. V. Pilipenko, et al.
Published: (2017-05-01)

IMPROVEMENT OF CALIBRATION OF CONE-SHAPED ROLLS OF THE PIERCING MILL OF THE PIPE-ROLLING SHOP
by: V. S. Korovin, et al.
Published: (2017-07-01)

Optimization and Finite Element Simulation of Wear Prediction Model for Hot Rolling Rolls
by: Xiaodong Zhang, et al.
Published: (2025-04-01)

Dynamic Modeling and Analysis of Rolling Bearing with Compound Fault on Raceway and Rolling Element
by: Xin Zhang, et al.
Published: (2020-01-01)

DEFINITION OF CONDITIONS OF STRIP’S ROLLING IN ROLLS OF UNEQUAL DIAMETER WITH FIXING OF AN ENDING ELEMENT
by: L. A. Isaevich, et al.
Published: (2016-12-01)

Analysis of the influence parameters on steel strip defects in continuous roll casting-rolling
by: Alexey Nogovitsyn, et al.
Published: (2023-12-01)

Research of Surface Residual Stress Strengthening with Rolling for Anti-roll Torsion Bar
by: ZOU Min-jia, et al.
Published: (2012-01-01)

Effect of rolling direction on mechanical properties of powder-rolled porous titanium plates
by: ZHAO Shao-yang, et al.
Published: (2022-04-01)